How To Install Bifold Closet Doors Youtube

It seems every house built since the 1950s has closets with sliding doors. Space-saving, sure, but non the best-looking—and certainly not very revealing when you're trying to run across (or reach) the appurtenances in the middle of the closet where the doors overlap each other.

Heavy bifold doors with a sturdy rails, on the other hand, move effortlessly abroad from the heart of the cupboard to give you a full picture of the contents inside. And because bifolds come in a wide array of profiles, they bring grapheme to a plain opening. Replacing those hollow-core builder's specials with a pair of weighty solid folders isn't a huge deal; the whole assembly and installation will have you lot a mere Sabbatum afternoon. Follow our footstep-past-step guide to DIY bifold doors and you'll be rewarded with a wide-angle view when it'southward time to pick out the day'south duds.

Step i

Bifold Doors Overview

Bifold doors are much like any doors, but connected into pairs with hinges and hung on a rails. What makes them look good and work well are a solid, heavy construction and sturdy and advisedly adjusted hardware.

The heft of the doors is what keeps them from shuddering when yous open them. So information technology'due south best to wait for solid–cadre or solid–woods doors, which will feel more substantial than hollow–core doors. (Solid doors are also easier to trim if any part of your door opening is out of foursquare.) Then, in order to handle the weight of these heavier doors, you'll demand a track that includes a wheeled machinery, which allows the doors to glide smoothly rather than shimmy along the track.

The most difficult—and sometimes most frustrating—part of the installation is attaching and adjusting all the hardware. The runway, the pivots, the hinges all accept to be assembled just so, and it's worth taking the time to double–check every measurement and position to be sure each slice is in the right identify and facing the right way.

Step 2

Mount the hinges

Finish or pigment the doors earlier starting. Label the doors to show the order they'll be installed and which sides face out.

Take a jamb side door and mark its inner edge eleven inches from the bottom, 7 inches from the pinnacle, and centered between the two. Identify the door on edge with the marks facing up.

Accept the lower half of a hinge and marshal its lesser with the bottom mark, its duke facing back and flush to the edge. Use a self?centering bit to drill pilot holes through the swivel holes. Screw on the hinge plate. Attach the top and middle hinges, on their marks.

Identify the leading (inner) door on edge, facing back-to-back with the offset door. Align the doors evenly confronting a foursquare, then put the hinges together. Screw the hinge plates to the leading door. Repeat on the second pair of doors.

Footstep 3

Attach the rails hardware

Spike the pivot plates (the pins that fit into the rails and the flooring bracket), and the locking arms (the hooks that slide along the rail) to the top and bottom of each gear up of doors. The pivot plates go on the tops and bottoms of the jamb–side doors, and the locking arm on the tops of the leading doors.

Each kit requires its hardware to exist uniquely positioned, and so check the diagrams that come with yours for exact measurements and placements. These will tell y'all, for case, not only how far a pivot plate should exist from the door edges around it only also where its pin should be in relation to the door'due south edges. Adhering to all the given dimensions ensures that no piece goes on backward.

Pace 4

Install the rails

Use a hacksaw to cut the track to length to fit the closet opening. Slide the hanging hardware into the track—the small-scale stops in the center, then around them the track hangers with wheels, and finally the pivot socket on the exterior.

Attach the track to the door header with the screws provided. Position the rails 1 inch in from the front border of the header. This will requite you plenty room to hide the track with trim without limiting the door action.

Tip:Don't tighten the hardware onto the track. Information technology will be easier to hang the doors later if the pieces are loose.

Step 5

Position the floor bracket

Use the measurements supplied by the manufacturer to position the floor bracket next to the door jamb.

Hang a plumb bob from the heart of the track above the floor subclass to align the pin pigsty in the subclass front end to back. This will ensure that the doors are plumb when installed. Outline the bracket in pencil to marker its exact location.

Spiral the bracket in place, then remove the screws and prepare the bracket and screws aside.

Footstep 6

Hang the doors

Bring the doors to the track and lift the jamb side to hook the pin of the top pivot plate into the pin socket. Make sure the pin is all the way in, then push the lever on the side of the socket to lock it in identify.

Slot the pin from the track hanger into the locking arm on the leading door. Twist the arm to lock it into identify. With the doors closed, swing them frontwards enough to grab the flooring bracket in the lesser pivot pin.

Step 7

Attach the floor bracket

Swing the doors back into identify and align the floor subclass with the pencil marks. Use a flexible bit extender to screw down the bracket.

Hang the other gear up of doors. Close both sets and adjust them along the track to even up the reveal around them. Then, using the wrench provided with the hardware, tighten the pivot sockets on the ends of the rails and the small stops in the center.

Tip: Enquire a helper to requite yous a paw in lifting and belongings the doors, which can exist unwieldy.

Pace 8

Attach the door aligner

From within the closet and with the doors closed, mount the door aligners betwixt the two leading doors, 6 inches upward from the floor. The aligners take hold of when the doors are closed, keeping the door faces flush with each other.

From outside the closet, bank check the alignment. Adjust the track hardware as necessary to keep the reveal around the doors fifty-fifty.

Step nine

Install the door pulls

For flat doors, mensurate 36 inches from the flooring on each leading door. Then mark the center, side-to-side, at that height. For paneled doors, detect the centre of the centre rail instead. Agree a straightedge diagonally from corner to corner on the track, draw a line in the middle, then switch to the other diagonal and cantankerous the line. The X marks the rails's middle.

Drill three/16?inch holes at each mark and spiral on door pulls.

Cut a slice of 1x2 stock the width of the closet opening to conceal the runway. Prime number the trim and let it dry. Use a 1/sixteen?inch bit to drill pilot holes through the underside of the trim into the header. Spiral the trim to the header with two½?inch trim screws. Fill up the screw holes, and so paint the trim to match the casing.

Source: https://www.thisoldhouse.com/doors/21016678/how-to-install-bifold-doors

Posted by: hallmusenchently40.blogspot.com